This Coil Cutter Kit is for use with a #30 Foredom flex shaft handpiece only. Kit includes: Aluminum 6" long coil holder block and steel top plate for holder; Saw blade, guard for Foredom #30 Flexshaft handpiece with adapter bushing, 1 saw arbor to fit 3/8" hole blades. Coils to be cut can be up to 4 inches long and 7/8 inch (22 mm) in outside diameter. Coils may be made of 16 through 30 gauge wire.
Set 28 of mandrels. Sizes range from 3/32" to 1/2" by 64ths of an inch. NOTE: Current mandrels don't include notches at base. Simply insert your wire into the chuck with the mandrel, and make sure the wire is secured in the jaws before winding. The notch isn't necessary.
Metric mandrels from 1mm to 13 mm Mandrels are transfer punch sets. You can purchase transfer punch sets elsewhere if necessary, we offer it as a service so you can get everything at one place. NOTE: Current mandrels don't include notches at base. Simply insert your wire into the chuck with the mandrel, and make sure the wire is secured in the jaws before winding. The notch isn't necessary.
The saws are finally here! This saw frame, 100% made in the USA by Potter USA, is one of the finest quality saws on the market today. Its rigid, stainless steel frame is well-balanced and is great for detailed sawing and piercing. The frame is a little heavier than a standard, adjustable German-style saw frame, which helps with momentum when sawing.
This easy-to-use ear wire jig makes it easy to make repeatable, consistently sized kidney-style ear wires. This tool is NOT used in a hydraulic press. Finished ear wire is approx. 7/8" long, 3/8" wide, and features an outward bend in the end of the wire and catch for a secure hold. The loop is approx. 3mm diameter. Recommended for use with half-hard 20g wire.
This easy-to-use ear wire jig makes it easy to make repeatable, consistently sized shepherd’s hook-style ear wires. See long description for instructions, and watch the video below (coming soon)! This tool is NOT used in a hydraulic press. Finished ear wire is approx. 25mm long, 10.5mm wide, and features an outward bend in the end of the wire to help secure it in the ear when worn. The loop is approx. 3mm diameter. Recommended for use with 20g wire with a balled-up end.
This easy-to-use ear wire jig makes it easy to make repeatable, consistently sized shepherd’s hook-style ear wires. See long description for instructions, and watch the video below! This tool is NOT used in a hydraulic press. Finished ear wire is approx. 22mm long, 10.5mm wide, and features an outward bend in the end of the wire to help secure it in the ear when worn.
This mount is meant to be used with our wire-forming tools. Each wire-forming tool includes two mounting holes that fit securely onto the pegs in this mount. The mount has two holes where it can be secured to a work surface with screws. Once attached to a work surface, each wire-forming tool can be dropped down onto the mount and held securely in place with the pegs. Changing out tools is as easy as lifting the wire former off the pegs and replacing it with a different wire former. The mount measures 5" x 2". Wire forming tools SOLD SEPARATELY.
This Coil Cutter Kit is for use with a DREMEL only. See below for specifics. Kit includes: Aluminum 6" long coil holder block and steel top plate for holder; Saw blade, guard for Dremel with adapter bushing, 1 saw arbor to fit 3/8" hole blades. Coils to be cut can be up to 4 inches long and 7/8 inch (22 mm) in outside diameter. Coils may be made of 16 through 30 gauge wire. (NOTE: Does not fit battery-powered, cordless or very old Dremels). We use a Dremel 200 here in our shop.