(0) items
You have no items in your shopping cart.
All Categories


    This section includes sides of rings with great design, or entire bands. 
    View as Grid List
    Sort by
    Display per page

    Impression Die Fancy Ring Shank

    1/8" wide at band and 3/8" wide at top  x  1 1/4" tall Imp1ression dies should be used in a hydraulic press

    Impression Die Wheat Ring

    This wheat pattern impression die is 2.5 inches (actual pattern) long. The pattern is 3/16th wide. Can be used with a mallet or in the hydraulic press.

    Impression Die Victorian Ring Shank

    It is .5" at the widest point on top. The narrow part on the bottom is .25" The length is 1 1/8" Impression dies should be used in a hydraulic press

    Impression Die Heart Ring Band

    This die must be used in a hydraulic press. This die measures 2" long x 1/4" wide

    Impression Die Vined Ring Shank

    This die must be used in a hydraulic press. This die measures 3/16" at the band, 11/16" at the top, and 1 1/2" in length

    Impression Die Infinity Band

    This die must be used in a hydraulic press. This die measures 1/4"  x  1 1/4"

    Impression Die Wide Ring Flower

    3.25 inches long x 3/8 inch tall or 82mm x 9.5mm

    Pattern Bar Levels

    These Pattern Impression Bars are great for making ring bands, pattern metal, and bangles! The pattern is from end to end so you can feed the metal through to make longer strips! The pattern is 3'' long.

    Impression Die Morse Code Band

    1/8" x 2 3/4"W or 70mm x 3mm

    Impression Die Small Flowers Band

    3/16" H x 2 1/4" W or 5mm x 57mm

    Impression Die Thick Rope Band

    1/4" H x 3 1/4"W or 6mm x 82mm This die must be used in a hydraulic press. This design will run off the edge of the die so that you can feed your metal through to make a continuous pattern.

    Impression Die Three Flower Band

    5/16" H x 2 1/2" W or 8mm x 64mm

    Impression Die Art Deco Diamond Ring

    2 1/4 x 1/4" or 57mm x 6mm

    Impression Die Art Deco Stone Set Ring

    2 1/4" x 3/16" or 57mm x 5mm

    Impression Die Art Deco Center Stone Ring

    2 1/4" x 5/16" or 57mm x 8mm

    Impression Die Art Deco Segment Ring

    2 5/16" x 3/16" or 59mm x 5mm

    Impression Die Traditional Prong Ring

    2" x 5/16" or 51mm x 8mm

    Impression Die Ribbon Ring Band

    2 5/8" x 3/16" or 67mm x 5mm

    Impression Die Stone Oval Ring

    3" x 3/8" or 76mm x 9.5mm

    Impression Die Small Snake Skin

    2 3/16" x 1/8" or 56mm x 3mm

    Impression Die Fine Twisted Band

    2 3/4" x 1/16" or 70mm x 1.5mm

    Impression Die Double Ridge Band

    2" x 3/16" or 51mm x 5mm

    Impression Die Medium Twisted Rope

    2 1/4" x 3/16" or 57mm x 5mm

    Stamp Border Holder

    1.5 inches tall x 2.75 inches wide. Opening to place a border stamp is 3/8 inches and has three bolts to tighten it in place. Two strong magnets are placed in top of holder so it will attach to the top of any hydraulic press and stay in place. See video in full description.

    Wire Die Pusher

    Properly heat treated hi carbon steel. For use in Stamp Border Holder to push wire into certain ring impression dies.

    Impression Die Wings of Flight

    7/16" x 2 7/16" or 11mm x 62mm

    Impression Die Arrow Ring

    1/4" x 1 15/16" or 6mm x 49mm

    Impression Die Beaded Ring

    1/4" x 2 1/4" or 6mm x 57mm

    Impression Die Square Inlet Band

    1/4" x 2 3/8" or 6mm x 60.5mm Internal Square: 1/4"

    Impression Die Simple Band

    3/16" x 2 7/16" or 5mm x 62mm

    Impression Die Art Nouveau Ring

    3/16" x 3 1/8" or 5mm x 79mm

    Impression Die Athenian Ring

    3/16" x 2 5/16" or 5mm x 59mm

    Impression Die Split N Ring

    5/16" x 2 3/4" or 8mm x 70mm

    Impression Die Lightning Ring Shank

    5/16" x 2 1/8" or 8mm x 54mm

    Impression Die Teeth Ring Shank

    5/16" x 2 1/2" or 8mm x 64mm

    Impression Die The Walking Stick

    3/16" x 2" or 5mm x 51mm